A gap in a timber floor may look like a simple hole waiting to be filled with timber floor filler. Sometimes it is. Other times, that gap is moving with the seasons, warning of moisture trouble, or hiding a deeper subfloor problem.
The short answer: Small nail holes, minor surface defects, and stable joints up to 2 mm can usually be filled with a compatible timber floor filler during the sanding process. Do not fill expansion joints or gaps caused by seasonal movement, loose boards, or moisture problems without investigating the underlying cause first.
Why Do Timber Floor Gaps Appear?
Timber responds naturally to its surroundings. It releases moisture and shrinks when conditions become dry, then absorbs moisture and expands again when indoor humidity rises.
Because of this seasonal movement, a gap that appears wide during a dry month may close up later in the year. Applying a wood floor filler while a gap is at its widest can cause the dried filler to crack, lift, or squeeze out as the boards expand.
Other common causes of floor gaps include:
- Incorrect moisture acclimatisation during installation
- Seasonal shifts in indoor humidity
- Loose, cupped, or damaged floorboards
- Debris or old coating buildup trapped between boards
- Poor subfloor support or movement
- Natural settling in an older timber floor
Before selecting a timber floor filler, check whether the gaps remain stable throughout the year.
Which Gaps Can Usually Be Filled?
Use this as a starting point, not as a replacement for the filler manufacturer’s instructions.
| Floor condition | Should it be filled? | Recommended Action |
|---|---|---|
| Punched nail holes | Yes | Fill with a compatible wood putty or sanding-dust filler. |
| Small surface cracks in a board | Often | Fill if the board itself is structurally sound and stable. |
| Fine, stable joints (up to 2mm) | Possibly | Fill within the product’s stated maximum gap limit. |
| Large gaps between boards (over 2mm) | No | Use timber slivers, board replacement, or a specialist repair. |
| Seasonal gaps that open and close | No | Standard filler will likely crack or break loose as boards move. |
| Loose, cupped or damaged boards | No | Fix the subfloor or board movement before filling or sanding. |
| Gaps linked to moisture problems | No | Identify and resolve the moisture source before sanding. |
| Designed expansion or movement joints | No | Leave clear to meet flooring manufacturer expansion requirements. |
Every filler has limits. For example, Portcork’s Bona Mix & Fill is designed for suitable minor defects and joints up to 2 mm when mixed with fine, clean sanding dust. However, Bona advises that gaps in plank and end-grain floors are normally left unfilled because timber movement may cause the dried filler to break loose.
When Should You Avoid Using Timber Floor Filler?
Timber floor filler is not a structural repair.
Avoid filling over a problem simply to make the floor look smooth. Stop and assess the floor if you notice:
- Boards flexing or moving when walked on
- Significant cupping, crowning, or lifting
- Dampness, staining, or signs of water entry
- Repeated filler failure from previous sanding jobs
- Very wide or uneven gaps between boards
- Splintered or damaged board edges
- Gaps that open and close noticeably with the seasons
Large gaps may require timber slivers, board repairs or another specialist method. If moisture or movement is involved, filling and sanding may only hide the problem for a short time.
Should You Fill Before or After Sanding?
For a complete floor-filling system, the usual process involves an initial sanding stage followed by filling and finer sanding. The early sanding produces clean timber dust and exposes gaps that were hidden by old coatings or dirt.
A common sequence is:
- Inspect the floor and identify movement or moisture problems.
- Punch exposed nails below the timber surface.
- Perform the initial sanding cut to the preparation grit specified by your chosen filler.
- Vacuum joints thoroughly using suitable dust extraction to remove loose dust and debris.
- Apply the timber floor filler across the defects or joints according to its Technical Data Sheet.
- Allow the filler to dry completely before sanding again.
- Complete the finer sanding sequence to remove excess surface filler and smooth the timber.
- Apply a compatible primer and coating system.
The exact process can change with the floor, filler and finish. Some nail-hole fillers may be used at a different stage, so check the full coating system before starting.
Choosing the Right Timber Floor Filler
Different defects and flooring systems need different products.
Bona Mix & Fill is a water-based binder designed to be mixed with fine, clean timber sanding dust. It may be used for suitable minor defects and joints up to 2 mm. Bona normally advises against filling gaps in plank and end-grain floors where timber movement may loosen the dried filler.
LOBA Easy Fill is intended for filling suitable joints and minor damage in bonded parquet and hardwood floors. LOBA advises that old floors with wide or dirty joints, along with nailed or screwed flooring, are not generally filled because the dried material may break loose.
A ready-mixed timber putty may suit individual nail holes or isolated defects. Whichever product is selected, it must be suitable for the floor’s construction and compatible with the primer, stain and finish applied later.
Check:
- Maximum recommended gap size
- Suitable sanding-dust grade
- Drying and sanding time
- Coating compatibility
- Whether the product accepts stain
- Indoor-use requirements
Always test the complete filler and coating system in a small area. Filler can absorb stain differently from the surrounding timber, so a perfect colour match is not guaranteed.
Safety When Sanding Timber Floors
Prepare the Floor, Not Just the Gap
The best timber floor filler cannot correct moving boards, excess moisture or poor preparation.
Start by understanding why the gap exists. Fill small, stable defects with a compatible product, but investigate wider or changing gaps before sanding.
Explore Portcork’s range of timber floor fillers, sanding products and floor finishes, or contact the Portcork team for help choosing products that work together.
Frequently Asked Questions
Can I make timber floor filler with sanding dust?
Yes, provided you mix the dust with a dedicated binder, such as Bona Mix & Fill that is specifically formulated for sanding dust. Always use clean, fine dust from the same timber species and follow the mixing ratios in the product’s Technical Data Sheet.
How wide a gap can you fill in a timber floor?
Most trowel-applied timber floor fillers are rated for fine, stable gaps up to 2 mm wide. Gaps wider than 2 mm are prone to cracking and shrinking, and usually require timber slivers, board replacement, or a flexible specialist joint sealant instead.
Why does timber floor filler crack or fall out?
Floor filler typically fails due to seasonal expansion and contraction of the timber, flexing floorboards, trapped dirt in the joints, or applying filler to gaps wider than the manufacturer’s recommended limit.
Can filler stop floorboards from moving?
No. Timber floor filler improves surface appearance and smoothness, but it does not bond floorboards together or repair subfloor movement. Loose boards must be mechanically secured before sanding.
Can timber floor filler be stained?
Some timber floor fillers and dust binders accept stain, though cured filler often absorbs colour differently from natural timber grain. Always test your chosen filler, stain, and finish together on a sample board before treating the entire floor.


